路由器不认ADSL模块的解决办法

路由器装上WIC-1ADSL后系统中无法看到端口ATM0，一般来说是因为IOS版本不支持，比如2600上C2600-i-mz.122-8.T5.bin就不支持，这时会有一些错误提示，比如显示00:00:09: %SYS-2-GETBUF: Bad getbuffer, bytes= 68444513

-Process= "Init", ipl= 0, pid= 2

-Traceback= 80378168 8081667C 80816568 8041BBC4 8041BDC0 8041C0B8 803142EC 803E9

1C4　把卡拔掉就没有这个显示了；

这时可以将IOS升级，比如flash:c2600-ik8s-mz.122-11.T.bin就肯定好使；

正常SHOW RUN的时候可以看到下面类似显示

interface ATM0/0

no ip address

shutdown

no atm ilmi-keepalive

dsl operating-mode auto

SHOW VER也可以显示模块信息如下：

Cisco Internetwork Operating System Software

IOS (tm) C2600 Software (C2600-IK8S-M), Version 12.2(11)T,　RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2002 by cisco Systems, Inc.

Compiled Thu 01-Aug-02 16:56 by ccai

Image text-base: 0x8000809C, data-base: 0x817DAFD8

ROM: System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)

jngs uptime is 4 minutes

System returned to ROM by power-on

System image file is "flash:c2600-ik8s-mz.122-11.T.bin"

cisco 2621XM (MPC860P) processor (revision 0x100) with 60416K/5120K bytes of mem ory.

Processor board ID JPE072410L3 (3444616740)

M860 processor: part number 0, mask 32

Bridging software.

X.25 software, Version 3.0.0.

2 FastEthernet/IEEE 802.3

2 FastEthernet/IEEE 802.3 interface(s)

1 ATM network interface(s)

32K bytes of non-volatile configuration memory.

32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x3922

到底模块是否好用可以通过SHOW DIAG 初步判断

显示如下

Slot 0:

C2621XM 2FE Mainboard Port adapter, 3 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware Revision: 1.0

PCB Serial Number: JPE072410L3 (3444616740)

Part Number　: 73-7754-02

RMA History　: 00

RMA Number　 : 0-0-0-0

Board Revision　 : A0

Deviation Number : 0-0

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 03 6D 41 01 00 C1 18 4A 50 45 30 37 32

0x10: 34 31 30 4C 33 20 28 33 34 34 34 36 31 36 37 34 &n

bsp;0x20: 30 29 82 49 1E 4A 02 04 00 81 00 00 00 00 42 41

0x30: 30 80 00 00 00 00 FF FF FF FF FF FF FF FF FF FF

0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

WIC Slot 0:

DSL SAR (ADSL)清晰的表示能看到硬件

Hardware Revision: 2.3

Part Number　: 73-4771-08

Board Revision　 : A0

Deviation Number : 0-0

Fab Version　: 05

PCB Serial Number: JAB061509QZ

RMA Test History : 00

RMA Number　 : 0-0-0-0

RMA History　: 00

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 00 2E 41 02 03 82 49 12 A3 08 42 41 30

0x10: 80 00 00 00 00 02 05 C1 8B 4A 41 42 30 36 31 35

0x20: 30 39 51 5A 03 00 81 00 00 00 00 04 00 FF FF FF

0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF