鉴于大家对模具专业十分关注,我们编辑小组在此为大家搜集整理了“后接头落料模设计”一文,供大家参考学习!
论文编号:JX1676 论文字数:11233.页数:25 附任务书,开题报告,外文翻译,答辩PPT,CAD图
600)makesmallpic(this,600,1800);'' src="http://myeducs.cn/44/7062_20120929200910_leswn.png" width="389" height="76" border="0" title="后接头落料模设计.png" />
后接头落料模设计
【摘要】冲压模具在实际工业生产中应用广泛。在传统的工业生产中,工人生产的劳动强度大、劳动量大,严重影响生产效率的提高。随着当今科技的发展, 工业生产中模具的使用已经越来越引起人们的重视,冲压模具可以大大的提高劳动生产效率,减轻工人负担,具有重要的技术进步意义和经济价值,而被大量应用到工业生产中来。 本文对自行车上的后接头零件的冲裁工艺性进行了分析,从而确定工件的工艺方案。紧接着对模具的主体部分进行了详细的设计,包括工件的冲压工艺计算和模具总体结构设计。这两部分重点介绍了模具尺寸的确定、工艺力计算、压力机的选择以及模具结构的设计、各种标准件的选用以及模具材料的选用等等。
【关键词】冲压 模具 设计
Design of blanking die for the rear connector
[Abstract] Punching die has been widely used in industrial production. In the traditional industrial production, the worker work very hard, and there are too much work, so the efficiency is low. With the development of the science and technology nowadays, the use of punching die in the industial production gain more attention, Punching die could increase the efficience of production and could alleviate the work burden, so it has significant meaning in technologic progress and economic value, and be used in the industrial production more and more.
The article has carried on the analysis to the work piece blanking technology capability. The article carries on the analysis to the work piece technology capability, thus determination work piece craft plan. The following closely starts this article key design part - - work piece ramming process design and the mold system design.These two parts introduced with emphasis the mold size determination, the craft strength computation, the press choice as well as the mold structure design, each kind of standard letter selection as well as the mold material selects and so on.
【Key words】punching molding tool design
目 录
设计任务书 Ⅰ
开题报告 Ⅱ
中外文摘要 Ⅵ
前言 1
1 选题背景 3
1.1 题目来源 3
1.2 研究目的和意义 3
1.3 国内外研究现状、发展趋势及存在的主要问题 3
2 零件加工工艺分析 6
2.1 产品尺寸精度,粗糙度、断面质量分析 7
2.2 产品的材料分析 7
3 确定冲裁工艺方案及模具结构形式 7
4 模具设计计算 7
4.1排样设计 7
4.2冲裁工序力的计算 8
4.3确定压力中心 9
4.4计算模具刃口尺寸 9
4.5压力机的选择 12
5 冲模零部件的设计 12
5.1 凹模的设计与固定 12
5.2凸摸的设计 13
5.3卸料板的设计 14
5.4模架的选用 14
5.5紧固件的选用 16
5.6材料的选用 16
6模具的部分图纸 17
7 冲压模具的安装、调试 19
7.1 模具的安装的一般顺序 19
7.2 冲模的试冲和调整 20
总结 21
参考文献 22
致 谢 23